The original Eco Filter consists of two Micro Cut Filters (electrostatic filters), a pre-filter and a main filter, which use an ion effect to collect extremely small dust particles. The pre-filter has a honeycomb configuration and the main filter is pleated to achieve a large surface area that raises its dust collecting performance. Thanks to these features, the Eco Filter has a replacement cycle of up to 12,000 hours, * which reduces the hassle of maintenance. And, as an environmental consideration, the filter can be washed with water and reused.**
The usage environment affects the duration of the filter.
When washing with water, please follow the procedures listed in the operating instructions.
Also, we recommend replacing the filter with a new one after it has been washed and reused twice.
If the filter is not sufficiently clean after washing, replace it with a new one
Dual-Lamp System Prevents Image Interruptions
The Dual-Lamp System eliminates the need to interrupt a presentation if a lamp should burn out (in dual-lamp operation mode). The Lamp Relay mode also operates the lamps alternately to enable 24/7 projector operation.
Flexible Installation
The wide adjustment range of the powered horizontal/vertical lens shift function assures convenience and versatility during installation. It lets you easily make adjustments with the remote control. The unit can also be rotated 360 degrees vertically. This means you can install it at any angle you want, to accommodate different installation conditions.
A Wide Range of Optional Lenses
Choose from a wide lineup of optional lenses for your system, including short-throw, long-throw zoom and fixed-throw lenses for rear projection use. The additional lenses make it easy to adapt your projector to the installation site. The lenses attach and detach with one-touch ease.
Lens-centered design
A lens-centered, symmetrical design provides ease of installation, eliminating the need for any special considerations when planning the installation site.
Easy replacement of Filter and Lamp
An Eco Filter is replaced from the side and lamps are replaced from the back panel. Both of them are replaced very easily even after the projector is installed on the ceiling.
Multi-Screen Support System Seamlessly Connects Multiple Screens
The Multi-Screen Support System optimally adjusts multiple screens: Edge blending, color matching and multi-screen processor.
Edge Blending
The edges of adjacent screens can be blended and their luminance controlled.
Color Matching
This function corrects for slight variations in the color reproduction range of individual projectors.
Multi-Screen Processor
The PT-DZ770 Series projectors can project large, multi-screen images without any additional equipment. Up to 100 units (10 x 10) can be edge-blended at a time.
Versatile System Configurations Match a Variety of Applications
The wide-ranging terminals include 2 sets of RGB inputs (compatible with Y/PB/PRsignals), an HDMI input,
and a DVI-D input. A serial input/output terminal (RS-232C compliant) that allows remote operation from a PC,similar to that of a wireless remote control, and a remote terminal for input switching by contact control andstandby ON/OFF operation also make it possible to configure a remote operation system.
Easy Remote Monitoring and Control over a LAN
Web browser on a computer connected through a wired LAN system lets you remotely operate projectors and check their status. An e-mail messaging function can also notify you when a lamp needs replacement, and indicate the overall projector status.
In addition, Multi Projector Monitoring and Control Software is available for monitoring and controlling multiple Panasonic projectors from a single PC.
The wired LAN terminal is compatible with PJLink (class1), an open protocol that is used by many manufacturers, to enable integrated control of systems that contain different brands of projectors.
Crestron RoomView and AMX Device Discovery
The LAN terminal allows a computer connected to the network to use Crestron RoomView application software to manage and control system devices. Besides, The AMX Device Discovery technology is built in thePT-DZ770 Series.
Wireless Remote Control with a Maximum Operating Range of 30m (98ft)
Wireless Remote Control provides greater convenience for large conference rooms, lecture halls and gymnasiums with large audiences. Also, two signal transmission ports are provided to enable a large operating area.
Standby Mode: Eco
The PT-DZ770 Series projectors have attained a low standby power level of 0.2 W** (standby mode: eco). It also helps to slash running costs, and reduces environmental impact.
When the standby mode is set to eco, network functions such as power on over the LAN will not operate. Also, only certain commands can be received for external control using the serial terminal.
For 120 V AC power supply. 0.3 W for 200-240 V AC power supply.
Made in Japan
The PT-DZ770 Series projectors are carefully manufactured at the Panasonic factory in Japan, under strict quality control. This is another, very important advantage of a Panasonic projector.
Other Valuable Features
3D color management system
HD IP conversion
Digital noise reduction
Dynamic sharpness control
Mechanical lens shutter
Direct Power Off allows unplugging the power cord right after use
Specifications:
General |
Power supply |
120 V AC, 7.5 A, 50/60 Hz, 220-240 V AC, 4.3 A, 50/60 Hz
|
Power consumption |
|
120 V AC |
790 W (830 VA) (0.2 W when STANDBY MODE set to ECO*1, 6 W when STANDBY MODE set to NORMAL)
|
220-240 V AC |
760 W (950 VA) (0.3 W when STANDBY MODE set to ECO*1, 8 W when STANDBY MODE set to NORMAL)
|
Dissipation BTU |
U models: max. 2,754 BTU/hour E, EJ models: max. 2,686 BTU/hour
|
DLP chip |
|
Panel size |
17.8 mm (0.7 inches) diagonal (4:3 aspect ratio)
|
Display method |
DLP chip x 1, DLP projection system
|
Pixels |
786,432 (1,024 x 768) pixels
|
Lens |
|
PT-DX810ES |
Powered zoom (throw ratio 1.8-2.5:1), powered focus F 1.7-1.9, f 25.6-35.7 mm
|
PT-DX810ELS |
Optional powered zoom/focus lenses and fixed-focus lens
|
Lamp |
300 W (max. 310 W) UHM lamp x 2
|
Screen size (diagonal) |
1.27-15.24 m (50-600 inches), 1.27-5.08 m (50-200 inches) with the ET-DLE055, 4:3 aspect ratio
|
Brightness*2 |
8,200 lm (dual-lamp, LAMP MODE: NORMAL)
|
Center-to-corner uniformity ratio*2 |
90%
|
Contrast ratio*2 |
2,000:1 (full on/full off, CONTRAST MODE: HIGH*4)
|
Resolution |
1,024 x 768 pixels (Input signals that exceed this resolution will be converted to 1,024 x 768 pixels.)
|
Scanning frequency |
|
HDMI/DVI-D |
fH: 15-91 kHz, fV: 50-85 Hz, dot clock: 25-162 MHz
|
RGB |
fH: 15-91 kHz, fV: 50-85 Hz, dot clock: 162 MHz or lower
|
YPBPR (YCBCR) |
fH: 15.75 kHz, fV: 60 Hz [480i (525i)] fH: 31.50 kHz, fV: 60 Hz [480p (525p)] fH: 45.00 kHz, fV: 60 Hz [720 (750)/60p] fH: 33.75 kHz, fV: 60 Hz [1035 (1125)/60i] fH: 28.13 kHz, fV: 50 Hz [1080 (1125)/50i] fH: 27.00 kHz, fV: 24 Hz [1080 (1125)/24p] fH: 33.75 kHz, fV: 30 Hz [1080 (1125)/30p] fH: 56.25 kHz, fV: 50 Hz [1080 (1125)/50p] fH: 15.63 kHz, fV: 50 Hz [576i (625i)] fH: 31.25 kHz, fV: 50 Hz [576p (625p)] fH: 37.50 kHz, fV: 50 Hz [720 (750)/50p] fH: 33.75 kHz, fV: 60 Hz [1080 (1125)/60i] fH: 28.13 kHz, fV: 25 Hz [1080 (1125)/25p] fH: 27.00 kHz, fV: 48 Hz [1080 (1125)/24sF] fH: 67.50 kHz, fV: 60 Hz [1080 (1125)/60p]
|
Video/ S-Video |
fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60], fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
|
Optical axis shift*5,/sup> |
|
Vertical |
+50% from center of screen (powered)*6
|
Horizontal |
10% from center of screen (powered)
|
Keystone correction range |
Vertical: 40 (30 with the ET-DLE055/DLE080)
|
Installation |
Ceiling/floor, front/rear
|
Terminals |
|
HDMI IN |
HDMI 19-pin x 1 (Deep Color*7, compatible with HDCP) 480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p, VGA (640 x 480)-WUXGA (1,920 x 1,200)*8, compatible with non-interlaced signals only, dot clock: 25-162 MHz
|
DVI-D IN |
DVI-D 24-pin x 1 (DVI 1.0 compliant, compatible with HDCP, compatible with single link only) 480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p, VGA (640 x 480)-WUXGA (1,920 x 1,200)*8, compatible with non-interlaced signals only, dot clock: 25 -162 MHz
|
RGB 1 IN |
BNC x 5 (RGB/YPBPR/YCBCR x 1)
|
RGB 2 IN |
D-Sub HD 15-pin (female) x 1 (RGB/YPBPR/YCBCR x 1)
|
VIDEO IN |
BNC x 1 (composite video)
|
S-VIDEO IN |
Mini DIN 4-pin x 1 (S-Video)
|
SERIAL IN |
D-sub 9-pin (female) x 1 for external control (RS-232C compliant)
|
SERIAL OUT |
D-sub 9-pin (male) x 1 for link control (RS-232C compliant)
|
REMOTE 1 IN |
M3 x 1 for wired remote control
|
REMOTE 1 OUT |
M3 x 1 for link control (for wired remote control)
|
REMOTE 2 IN |
D-sub 9-pin (female) x 1 for external control (parallel)
|
LAN |
RJ-45 x 1 (for network connection, 10Base-T/100Base-TX, compliant with PJLink)
|
Cabinet materials |
Cabinet materials
|
Dimensions (W H D) |
|
PT-DX810ES |
498 x 175*9 x 466 mm (19-19/32" x 6-7/8"*9 x 18-11/32")(with supplied lens)
|
Dimensions (W x H x D) |
|
PT-DX810ELS |
498 x 175*9 x 432 mm (19-19/32" x 6-7/8"*9 x 17") (without lens)
|
Weight*10 |
|
PT-DX810ES |
Approximately 16.3 kg (35.9 lbs) (with supplied lens)
|
PT-DX810ELS |
Approximately 15.4 kg (34.0 lbs) (without lens)
|
Operating environment |
Operating temperature: 0-45 C (32-113 F)*11, operating humidity: 20-80 % (no condensation)
|
Supplied accessories |
Power cord, power cord secure lock, wireless/wired remote control unit, batteries (R6/AA type x 2), software CD-ROM (Logo Transfer Software, Multi Projector Monitoring & Control Software) (x 1) |